Enterasys Matrix N7 7C107 Guide d'installation Page 53
- Page / 94
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Connecting to the Network
Matrix DFE-Platinum Series Installation Guide 3-23
ThefollowingproceduredescribeshowtoconnectanMT‐RJcable(Figure 3‐15)connector
toaMini‐GBICportconnector. ThisprocedurealsoappliestoanLCcable connector
shownin(Figure 3‐16).RefertoFigure 3‐15asanexampleandproceedasfollows:
1. Removetheprotectivecovers(not
shown)fromtheMT‐RJfiber‐opticportonthe
Mini‐GBICandfromtheconnectorsoneachendofthecable.
2. InserttheMT‐RJcableconnectorintotheMini‐GBICuntilitclicksintoplace.
Note: Leave the protective covers in place when the connectors are not in use to prevent
contamination.
Caution: Do not touch the ends of the fiber-optic strands, and do not let the ends come in
contact with dust, dirt, or other contaminants. Contamination of cable ends causes
problems in data transmissions. If the ends of the fiber-optic strands become
contaminated, use a canned duster to blow the surfaces clean. A cleaning swab saturated
with optical-grade isopropyl alcohol may also be used to clean the ends.
Precaución: No toque los extremos de los cables de fibra óptica y evite su contacto con
el polvo, la suciedad o con cualquier otro contaminante. Si los extremos de los cables se
ensucian, es posible que la transmisión de datos se vea afectada. Si nota que los
extremos de los cables de fibra óptica se ensucian, utilice aire comprimido para limpiarlos.
También puede limpiarlos con un estropajo embebido en alcohol isopropílico.
Note: To remove the MT-RJ cable connector, press on its release tab and pull it out of the
Mini-GBIC.
- Matrix DFE-Platinum Series 1
- Module 7G4280-19 1
- Installation Guide 1
- VCCI Notice 6
- BSMI EMC Statement — Taiwan 6
- Safety Information 6
- Class 1 Laser Transceivers 6
- Declaration of Conformity 7
- Enterasys Networks, Inc 8
- Firmware License Agreement 8
- Contents 11
- Chapter 4: Troubleshooting 12
- Appendix A: Specifications 12
- About This Guide 15
- Who Should Use This Guide 16
- How to Use This Guide 16
- Related Documents 17
- Introduction 19
- 1-2 Introduction 20
- 7G4280-19 21
- 5 GROUP SELECT switch 22
- Ethernet Interface Modules 23
- Connectivity 24
- Management 25
- Standards Compatibility 26
- LANVIEW Diagnostic LEDs 26
- Getting Help 26
- 1-10 Introduction 28
- Network Requirements 29
- 1000BASE-SX/LX/ELX Network 30
- 1000BASE-T Network 30
- Installation 31
- Unpacking the DFE Module 32
- Removing the Coverplate 33
- 3-4 Installation 34
- Preparation 35
- (MGBIC-02) 4 Port slot 37
- Removing the Mini-GBIC 38
- FTM1 and FTM2 Connectivity 39
- Module Placement and Rules 39
- Example 1 (Figure 3-6, A) 40
- Example 2 (Figure 3-6, B) 40
- Example 3 (Figure 3-6, C) 41
- Example 4 (Figure 3-6, D) 41
- Example 5 (Figure 3-6, E) 41
- 3-14 Installation 44
- Connecting to the Network 46
- Connections 47
- 3-18 Installation 48
- 3 UTP RJ45 cable connector 49
- 3-20 Installation 50
- Devices 51
- 2 Other device port 52
- 3 Release tab 54
- What Is Needed 56
- Mode 7 Bit Control 57
- Transmit Transmit=9600 57
- Bits Parity 8 Bits, No Parity 57
- Stop Bit 1 Stop Bit 57
- 3-28 Installation 58
- Connecting to a Modem 59
- 3-30 Installation 60
- RJ45 DB9 61
- RJ45 DB25 61
- Completing the Installation 62
- in the Matrix DFE-Platinum 63
- 3-34 Installation 64
- 3-36 Installation 66
- Troubleshooting 67
- Using LANVIEW Diagnostic LEDs 68
- 4-2 Troubleshooting 68
- Table 4-1 LANVIEW LEDs 69
- Troubleshooting Checklist 70
- 4-6 Troubleshooting 72
- Instructions) 73
- 4-8 Troubleshooting 74
- Specifications 75
- 7G4280-19 Specifications 76
- A-4 Specifications 78
- COM Port Pinout Assignments 81
- Regulatory Compliance 82
- Required Tools 83
- Setting the Mode Switches 83
- 1 Mode switch pack 84
- Memory Locations 85
- Memory Replacement Procedures 85
- Removing the DRAM SIMM 87
- Installing the DRAM SIMM 88
- DIMM Replacement Procedure 89
- Installing the DIMM 90
Produits connexes et manuels pour Mise en réseau Enterasys Matrix N7 7C107
Mise en réseau Enterasys 2000 Spécifications
(83 pages)
(83 pages)
Mise en réseau Enterasys 802.1Q Spécifications
(116 pages)
(116 pages)
Mise en réseau Enterasys 2H23-50R Spécifications
(808 pages)
(808 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels