Enterasys 2S4082-25-SYS Guide d'installation Page 37
- Page / 108
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installing the Chassis into a Rack
Enterasys NAC Controller Hardware Installation Guide 3-3
Wheninstallingtheswitchonaflatsurface,theinstallationoftherubberfeetisrecommendedto
preventtheswitchfromslidingonaflatsurface.Installingtherubberfeetisoptionalifyouare
installingtheswitchinarack.Toinstalltherubber feet,proceedto“InstallingtheRubber
Feet”
instructionsbelow.Forinstructionstorackmounttheswitch,proceedto“InstallingtheChassis
intoaRack”onpage3.
Installing the Rubber Feet
Toinstalltherubberfeetproceedasfollows:
1. Placetheswitchonitsbackonasturdyflatsurfacetogainaccesstothebottomofthechassis.
2. Removethefourrubberfeetfromtheirplasticbagintheshippingbox.
3. Locatethefourmarkedlocationsonthebottom fourcornersof
thechassis.
4. Removetheprotectivestripfromthebackofonerubberfootandpositionitonamarked
locationandpressfirmlyintoplace.Repeatthisproceduretoinstalltheremainingthree
rubberfeetintheotherthreelocations.
5. Afterinstallingtherubberfeet,returntheswitchtoitsuprightposition.
6. Forarackmountinstallation,proceed to “InstallingtheChassisintoaRack”onpage3.
Installing the Chassis into a Rack
TheEnterasys Matrix N1Chassiscan bemountedinastandardEIA‐310‐Dcompliant
48.26‐centimeter(19‐inch)equipmentrack.Tomountthechassisintoarackyoumustallowat
least60centimeters(24inches)ofclearanceinfrontoftherackforchassisinstallation.Thendecide
whethertoinstallthe
chassisonashelfintherack,ortoattachthechassisdirectlytotherack.
Installing the Chassis on the Rack Shelf
Toinstallthechassisonarackshelf:
1. KeepingtheaboveCautionnoteinmind,locatethepositionontherackwhereyouwillinstall
theshelf.
2. Referto“InstallingtheRubberFeet”onpage3.
3. Alignthefourholesintheearsoftheshelfwiththoseintherack,
thenfastentheshelftothe
rackusingfourofthescrewssuppliedwiththerack.
4. Afterinstallingtheshelf,proceedtoinstalltheEnterasys Matrix N1Chassisasdescribedin
“InstallingtheChassisDirectlytotheRack”onpage4.
Caution: Read Chapter 2 before completing the following procedure to ensure that all installation
guidelines are met.
Precaución: Antes de llevar a cabo el siguiente procedimiento, lea Chapter 2 para y asegúrese de
cumplir con todos los requisitos de instalación.
Note: In order to prevent a possible interference between the rack frame front and chassis rack
ears, the tapped rails may need to be adjusted such that they are recessed approximately 2 inches
behind the rack frame front. If the rack has a front door, this distance may need to be slightly more
depending on the door thickness.
- Enterasys 1
- orcontactEnterasys 5
- (Circuit Modules) 6
- (Circuit Breakers) 6
- VCCI Notice 7
- BSMI EMC Statement — Taiwan 7
- Safety Information 7
- Class 1 Laser Transceivers 7
- Declaration of Conformity 8
- Contents 11
- Chapter 5: Troubleshooting 12
- About This Guide 17
- Related Documents 18
- Typographical Conventions 19
- Commonly Used Acronyms 19
- Getting Help 20
- Introduction 21
- The N1-7C111 Chassis 22
- The NAC Controller PEP 22
- Overview 23
- 1-4 Introduction 24
- 1-6 Introduction 26
- Standards Compatibility 27
- LANVIEW Diagnostic LEDs 27
- 1-8 Introduction 28
- Site Guidelines 29
- Configuration Guidelines 30
- LANVIEW LEDs 30
- Link Aggregation 32
- 10BASE-T Network 32
- 100BASE-TX Network 32
- 1000BASE-T Network 32
- 1000BASE-SX/LX/ELX Network 33
- Order of Installation 36
- Installing the Rubber Feet 37
- N1 7C111 d 39
- Cooling Fans 40
- Required Tools 41
- Preparation 42
- engine o el módulo 42
- Installation 43
- (MGBIC-02) 4 Port slot 44
- Removing the Mini-GBIC 45
- Connecting to the Network 47
- Switches and End User Devices 49
- 2 Other device port 50
- 3 Release tab 52
- What Is Needed 54
- Connecting to a Modem 56
- RJ45 DB9 57
- Completing the Installation 58
- Enterasys Matrix 59
- Troubleshooting 61
- Using LANVIEW 62
- 5-2 Troubleshooting 62
- Table 5-1 LANVIEW LEDs 63
- Troubleshooting Checklist 64
- 5-6 Troubleshooting 66
- 5-8 Troubleshooting 68
- NAC Controller 74
- Setup the VLAN Configurations 84
- Physical Specifications 91
- Environmental Requirements 92
- Regulatory Requirements 92
- Specifications 93
- Specifications (continued) 94
- Item Specification 95
- Regulatory Compliance 100
- Mode Switch Bank Settings 101
- Location of Memory Modules 102
- Removing the DRAM SIMM 105
- Installing the DRAM SIMM 105
- Index-2 108
Produits connexes et manuels pour Mise en réseau Enterasys 2S4082-25-SYS
(142 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels